License Plates & Car Accessories

License Plates & Frames

Pressing Instructions for Sublimation License Plates and Frames

  • Temperature: 350F
  • Time: 60-75 seconds
  • Pressure: Light

* If colors are faded/dull, increase press temperature to 380F

  1. Print image in reverse
  2. Check for protective film prior to pressing
  3. Place in heat press with transfer on bottom
  4. Press according to above time/temperature/pressure
  5. After pressing, remove paper immediately.

Above instructions apply for the following license plates and frame models:

Sublimation Aluminum License Plate - 6" x 12" | D612
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

  • Temperature: 400F
  • Time: 30-45 seconds
  • Pressure: Medium
  1. Print image in reverse
  2. Check for protective film prior to pressing
  3. Place in heat press with transfer on top
  4. Press according to above time/temperature/pressure
  5. After pressing, remove paper immediately.

Above instructions apply for the following license plates and frame models:

License Plate Frame - 6.5" x 12.25" - White Sublimation Aluminum | SB4568
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

License Plate Frame - 6.5" x 12.25" - Full Design - White Sublimation Aluminum | SB4566
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

License Plate Frame - 6.46" x 12.21" - White Sublimation Aluminum | SB4567
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

License Plate - 5.875" x 11.875" - White Sublimation Aluminum | SB5656
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

Sublimation Aluminum Action Plate | SB4364
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

License Plate - 5.875" x 11.875" - Silver Sublimation Aluminum | SB5948
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

 

_______________________________________________________________________________________

Car Flags

Pressing Instructions for Sublimation Car Flags

  • Temperature: 400F
  • Time: 30-45 seconds
  • Pressure: Medium
  1. Print image in reverse
  2. Place in heat press with transfer on top
  3. Press according to above time/temperature/pressure
  4. After pressing, remove paper immediately.

* Do Not press nylon seem - it may melt
**For best results, use a teflon sheet or teflon pillow between the two layers to avoid image migration

Above instructions apply for the following car flag models:

Two-Sided Sublimation Car Flag and Pole - 10.75" x 15.25" | 2SCF
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

_______________________________________________________________________________________

Hitch Covers

Pressing Instructions for Sublimation Hitch Covers

  • Temperature: 400F
  • Time: 30-45 seconds
  • Pressure: Medium
  1. Print image in reverse
  2. Check for protective film prior to pressing
  3. Place in heat press with transfer on top
  4. Press according to above time/temperature/pressure
  5. After pressing, remove paper immediately.

Above instructions apply for the following hitch cover models:

Oval Trailer Hitch Cover w/ Sublimation Aluminum Plate | SB4045
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

Round Sublimation Aluminum Trailer Hitch Cover Insert | SB4048
PDF Template for Adobe Photoshop | EPS Template for Corel Draw & Illustrator

 

 

Share:
Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request